How to Clean Dirt Bike Plastics
Dirt bike plastics can quickly become dirty, which not only looks bad but can also affect the bike’s performance. Therefore, they need to be cleaned regularly with a strong detergent designed for plastic to remove all dirt and grime accumulated from riding on dusty trails or through muddy puddles.
In this guide, we will give you some instructions on how to clean dirt bike plastics with the household items you have so that you get started easily.
- Detergent designed for plastic
- Clean water
- Scrubbing brush or soft cloths
- Bucket of warm soapy water
- A toothbrush
Instructions: How to Clean Dirt Bike Plastics
Fill the bucket with a few liters of clean, lukewarm water. Add about two tablespoons of detergent to it and stir well until dissolved. (Do not add too much detergent as it can cause foam.
Rinse everything with clean water to remove residual soap and pat dry gently before storing again.
To rinse, use a toothbrush to scrub the plastic. Rinse with water and pat dry again before storing.
To protect them from UV rays, use car wax or other sealants as needed! Keep plastics looking fresh and new by cleaning after every ride!
Alternative Methods You Can Use
If the dirt is more than a surface-level clean, you will need to use something stronger. Use Armor All or any other plastic cleaner for deep cleaning and those pesky bugs that can sometimes be left behind on bike plastics! Just spray onto the desired areas of the vehicle’s plastic parts and let sit for at least five minutes before scrubbing with a cloth or brush.
Rinse thoroughly again after using this type of product so as not to leave behind excess residue. The best way to protect your bike from UV rays is by waxing it regularly. However, if that doesn’t work, then there are some options available on the market like PlastiDip, which acts as an additional layer over the original paint job (so no need to remove the original paint and to make it difficult to repaint later).
Tips To Make Dirt Bike Plastic look Shiny
- Wipe down the plastic with a mixture of water and soap.
- Use toothpaste to scrub the dirt off before rinsing it away. Rinsing in soapy water can cause corrosion if left on for too long while adding some vinegar to the rinse cupboard will help prevent this from happening (if you’re worried about your bike’s paint job).
- Abrasive cleaners like Comet or bleach should not be used as they may leave marks that are hard to remove later on.
- Use a soft brush to scrub stubborn dirt off the bike.
- To get rid of any stuck on the plastic, dip a rag in rubbing alcohol and rub it over them before washing with water and soap.
- The use of vinegar will prevent corrosion if left for too long, while adding some detergent will help clean your plastics even more effective than just plain water can do.
Things To Consider Before Cleaning Dirt Bike Plastics
- Clean plastics with a soft cloth and soap or detergent.
- Wipe off any dust that may be on the plastics before cleaning. This will help avoid scratching them while they are wet.
- Use warm water to rinse dirt bike plastics after you have cleaned them. Warm water is gentler than cold water and will help prevent the plastics from drying out.
- Dry dirt bike plastics with a clean, dry cloth or paper towel. Make sure to get all plastic surfaces, so it doesn’t look streaky when you’re done.
- If your dirt bike plastics are dirty enough to need more than one washing, try using an all-purpose cleaner.
- Avoid using abrasive cleaners for dirt bike plastics that contain chemicals like ammonia, bleach, or detergent, which can dry out and damage them over time.
- Allow dirt bike plastics to air-dry before sitting on the seat again, so you don’t get your clothes dirty from any residue left behind after cleaning.
Maintenance Guide For Dirt Bike Plastics
- Thoroughly wash off with water using soapy detergent mixed in if desired (dish soap works best), then rinse thoroughly. Repeat until all grit has been removed from surfaces.
- Buff dry with a lint-free rag. Wipe down again with a wet cloth to remove excess water droplets. If needed, use more soapy detergent mix and scrub away stubborn stains. Rinse off and buff dry.
- Use a plastic polish after every wash to remove pitting, scratches, swirls, and other damage from the plastics. This will also help protect them against future wear and tear. If you use an enzymatic cleaner like Lexol or Leatherique, then apply it first before polishing it with your favorite product.
- Wax any glossy surfaces for added protection. We recommend either Turtle Wax Endurance Shellac Paste Polish or Mothers California Gold Synthetic Sealant Glaze in Red (either applied with a clay bar).
- To remove bug splatters and other stains, start with a basic cleaner like Simple Green or isopropyl alcohol mixed half-and-half. Rinse off the soap residue with water to avoid streaks. Then follow up by using an enzyme degreaser such as Lexol or Leatherique if needed.
Frequently Asked Questions
Do I Need the Right Products to Clean Dirt Bikes Plastics?
Yes, you will need to purchase cleaning products specially made for dirt bikes and motorcycles. You also want to make sure that the cleaner is not going to scratch or otherwise damage your plastics.
What Materials Can Be Used in Order to Clean My Dirt Bike’s Plastics?
Use warm water mixed with soap applied using either an old toothbrush, sponge, rag, or other soft-bristled brush. Rinse with plain water until no more bubbles appear on the surface being cleaned. If needed, use a dishwasher-like product as well as some type of plastic polish after rinsing off any soapy residue from cleaners that might have left behind streaks or annoying smudges on your plastics.
How Do I Remove Stubborn Stains From My Dirt Bike’s Plastics?
If you have any tough spots that need more attention than what soap and water can do, then it might be time to bring out something stronger like acetone (nail polish remover), white vinegar mixed with baking soda, or even paint thinner.
Just don’t use these on clear plastic as they will change the color of them! Also, be sure not to get too carried away while scrubbing because this has been known to happen before! Only take the care necessary for whichever spot needs it most and rinse off with soap and water afterward.
How Do I Remove Bugs From My Plastics?
The best way to get rid of pesky insects is by making your own bug spray! Mix together one teaspoon of dishwashing liquid, a cup of white vinegar, and a gallon of warm water in a container that can be sprayed on the dirt bike’s plastics.
Spray it onto an area where you suspect there might be bugs, rinse off with soapy water if necessary, then repeat as needed until all pests are gone (good luck!). It can also help apply clear packing tape or take care not to leave any food out near your motorcycle for these critters.
You Can Check It Out to Get Scratches Out of Dirt Bike Plastics
Dirt bike plastics need to be cleaned regularly. Cleaning them is not a difficult task, but it does take some time and patience on the part of the rider. Follow these simple steps for how to clean dirt bike plastics, so you can enjoy riding them at their fullest potential!
There are several ways that you can clean your dirt bike plastics, from using soap and water or an all-purpose cleaner like Simple Green to using WD-40 with paper towels.
When cleaning any type of plastic material, the most important thing is getting into cracks and crevices where brake fluid might accumulate over time. This will help keep your brakes in better working order as well as get those dirty parts shining again!
You may read also: Best Dirt Bike Cleaner