How to Change a Dirt Bike Tire Without Spoons
If you are a dirt bike rider and have ever had to change a tire without spoons, this guide is for you. It may not be as easy as it sounds but with these step-by-step instructions, we hope that the task will be manageable by most riders. By following these instructions, You’ll know how to change a dirt bike tire without spoons, you can make sure that your ride is safe and smooth!
Materials Needed
- A pump or air compressor
- Wrench (or an adjustable wrench)
- Screwdriver (Phillips Head)
- Flathead screwdriver
- A socket wrench (or a ratchet)
Instructions of How to Change a Dirt Bike Tire Without Spoons
Step One:
Place the bike on its side so that you have access to the tire. The best spot is when it’s resting against a wall, but if not, try placing it sideways, so the rear wheel is facing away from you.
Step Two:
With the bike resting on its side, find the bolts that attach to both sides of your tire and remove them by turning counter-clockwise until they are loose enough for you to pull out with your hands. You will want to be careful when pulling these as not to yank them as you don’t want to rip the bolts out of the bike.
Step Three:
Once both bolts are removed, pull your tire off and set it aside so that it’s not in your way or touching anything else. You’ll also need to make sure that you watch for any excess dirt on the inside of your wheel rim, which could cause it to get stuck.
Step Four:
Clean the rim of your wheel by brushing off any excess dirt with a stiff brush or toothbrush and then rinse it out with water if possible, making sure not to leave anything in there that could cause damage when you put the new tire on.
Step Five:
Using your hands, insert the tube into the tire and use your fingers to ensure that it’s standing up on both ends.
Step Six:
Starting at one end of the tube, make a small hole in it with your nail or something sharp- this is where you will be inserting the air pump nozzle (or straw). You can then insert two spoons into opposite sides of the tire to help hold the tube in place.
Step Seven:
Once you have inserted and inflated your tire (using an air pump), use a knife or something sharp to cut away any excess of the sides of the tube that are poking out at both ends.
Step Eight:
After cutting, make sure to also trim off any protruding pieces of the tube from inside the tire.
Step Nine:
Once you have done all of these steps, reinstall your wheel nut and make sure to torque it down tight with a wrench- this will help ensure that your new tire stays in place!
You Can Check It Out to Put a Tube in a Dirt Bike Tire
Some Additional Precautions & Reminders
- Some people recommend using a board to hold the bike up while changing tires. This is helpful because it will prevent you from having your hands on the ground when working with an occupied dirt bike tire.
- Always wear safety equipment such as gloves, jackets, and goggles when handling any type of motorized vehicle or engine parts
- You should also make sure that there are no other vehicles around before getting started – this can be dangerous! If someone does show up, it’s best not to get involved in their drama and wait until they leave before continuing with what you’re doing.
- Always use caution while performing maintenance tasks on motored vehicles. There are many moving parts that could cause injury if handled incorrectly.
Frequently Asked Questions
What Is the Best Way to Change a Dirt Bike Tire if You Don’t Have Any Spoons?
Generally, the best way to change a dirt bike tire without spoons is with your fingers. With this method, you will need to use an air pressure gauge or have somebody else monitor it for you while you are changing the tire. The advantage of using your fingers instead of spoons is that by using them, there is less risk of damaging the tire with sharp edges.
How Often Should I Be Changing My Tires?
It is recommended to change your dirt bike tires every two years, or after about 1200 miles. This includes replacing the tubes and adding new sealant if possible. By following this recommendation, you will help keep your biking experience as safe as it can be!
How Do I Check My Tire Pressure?
You can use an air pressure gauge or have somebody else monitor it for you while you are changing the tire. The advantage of using your fingers instead of spoons is that by using them, there is less risk of damaging the tire with sharp edges.
Conclusion:
It’s possible to change a dirt bike tire without spoons. You just need the following things, and you’ll be on your way in no time! A wrench or pliers, a tube of slime sealant, new rim tape, and parts for mounting valves/rim lock ring onto the valve stem.
Your local motorcycle shop should have those items available or if not, they can order them for you ahead of time so they’re ready when you get there. If you have read this article on how to change a dirt bike tire without spoons, then it’s time for you to go out and change your tire using these tips.
Are You Searching the Best Dirt Bike Tool Kit? Click the link for Dirt Bike’s Top Tools Kits Collection.
You may read also – Best Dirt Bike Tire for Mud
Darren Matlock
Hi, I'm Darren. I love dirt bikes and everything about the off-road lifestyle. I'm passionate about motorbikes, cars, racing sports and going on adventures. If you're like me and enjoy extreme sports, you've come to the right place! I like to write articles about dirt bikes to help beginners get started. Whether you're interested in buying a dirt bike, ATV, motorcycle or want to ride for hobby, I hope my articles will inspire you to learn more about how this machine can be used to ride.
